Gunslinger Mark IV-17 Laser Target (17-3/16″) $699.00 + s/h (Ships UPS)
NEW! We’ve Improved our Laser Target! (A Gunslinger Timer and other accessories are Required for the Mark IV-17 Laser Target)(Includes Special Mark IV-17 Power Splitter & 2′ Blue Cat 5 Cable, for Practice Mode Training). Our Mark IV Laser Target are designed with our new Low Cost ($59) CFDA Gunslinger Lasers, so that it will only record a time on the initial pulse, letting you know that you are actually hitting a target, rather than sweeping on a continuous laser beam.. Optional Adjustable Tri-Pod (sold separately).
Note: If you wish to run this unit in Contest Mode, where a Timer Operator runs the unit from behind the shooter. This can be accomplished by either using a 25′ Blue Cat 5 to place the timer also behind the shooter, where the times must be read by the Timer Operator, just like normal shooting ranges are set up, OR, By using a Red 25′ Cat 5 Cable / with a Cat 5 Connector to extend ONLY the Start Button behind the shooter, so that times will still be displayed on top of the Laser Target. All Items can be ordered in the Timer Accessory Section of the CFDA General Store.
THIS PRODUCT IS AN ACCESSORY TO AND ONLY OPERATES WITH A GUNSLINGER TIMER (sold seperately)
20.5″ x 20.5″ x 3.5″ wood-framed housing, which makes it very adaptable to various mounting methods. Weight: 9.5 lbs.
17-3/16″ round target area on the front of the box is a white translucent lens, that is designed to simulate a CFDA Target with grease.
Works with any Red Laser, however it is specifically designed to operate with the CFDA Gunslinger 3,000 Lumen CFDA-45 Laser Cartridge, only available through CFDA.
Since the Mark IV-17 is 17-3/16″, place it at 15′, and 47″ from the floor to center. You will be simulating actual CFDA Wax Targets used in most CFDA Matches!
Controls & Operation
The control panel is now located on the back panel of the wood-framed housing. The shooter simply connects the Blue Cat 5 Cable from the Gunslinger Timer to the Control Panel Port. This Laser Target requires and additional lead coming from the power supply. It completely replaces the normal CFDA Target LED Light and Sensor. There is an LED Start Signal that appears through the lens in the center of Laser Target.
New- Mark IV Control Panel (Same for either Mark IV-8 (8″ Version) or Mark IV-17 (17-3/16″ Version):
Reaction, 15′, or 21′ Settings “Reaction”, is for pure time, which records the time at the speed of light, used for some reaction training techniques. “15′ “, automatically does the math and adds .022 seconds, which is the average wax bullet travel time for a target placed 15′ away, this is normally the factory setting. “21′ “, automatically does the math and adds .030, for those who wish to know what their time would be at 21′.
Mark IV Laser Targets operate in various lighting conditions, EVEN OUTDOORS (As long as it is not directly facing the sun). However, there can be some indoor lighting conditions such as very bright LED lights in the close vicinity of the target. Once power is connected to both the Gunslinger Timer and the Mark IV Laser Target, using the provided small screw driver, turn the Sensitivity Knob (clockwise) until the Red Light illuminates. Then, turn the Sensitivity Knob, slowly (counter-clockwise) until the Red Light goes off. If the unit is recording premature hits, then turn the Sensitivity Knob slightly (counter-clockwise). If the problem persists, you made need to make changes to either lighting conditions or locate the Mark IV in a different location. You might also try turning down the Gunslinger Timer Sensitivity.
Just operate the timer normally in either contest or practice mode according to the Gunslinger Timer Manual. Make sure the Sensitivity Knob on the timer is turned all the way (clock-wise).